VennHelix-01 Buy

Venn Helix-01 hub set

The hub that tightens under power.

A 72-tooth helical ratchet that tightens like a bolt as you pedal, a 41.5 mm angular contact bearing that keeps rolling under load, and a cold-forged shell. 348 g for the pair.

Venn Helix-01 rear and front hubs in shot-peened grey, the rear with its freehub
72THelical ratchet, engages within 5°
41.5 mmNano-coated angular contact bearing
348 gThe set: front 105 g, rear 243 g
2 yearsWarranty on materials and workmanship

Helical engagement

The harder you pedal, the tighter it meshes.

In an ordinary ratchet hub, springs push the drive rings together and a little play stays between the teeth. Every time you start to pedal, that play is taken up before the wheel is driven.

The Helix-01 engages the way a bolt tightens: the more force you put through the pedals, the firmer its two 72-tooth ratchet rings press together. The spring only starts the engagement; your pedalling finishes it. So the drive gets stiffer exactly when you push hardest, your power goes into the wheel at once, and the bearings take the load the way they are meant to. Under power there is no free play, out of the saddle, in a sprint or on a steep climb.

  • Teeth72, engagement within 5°
  • Ratchet steelSCM 415, hot forged, CNC machined, manganese phosphate coated
  • SpringFlat steel, more contact area than a round wire spring
Helix-01 helical drive: the freehub's helical spline and the 72-tooth ratchet ring

Rolling under load

Spins freely on the road, not just in your hand.

A hub that spins beautifully in a workstand can still drag with a rider on it. Ordinary radial bearings are built for loads straight through their centre; a wheel under a rider, a sprint or a hard corner loads them from the side as well.

Beside its two 6902 bearings, the Helix-01 rear hub runs an oversize 41.5 mm nano-coated angular contact bearing. It is made for those side loads, so its friction does not climb when you push hard or ride rough ground, and it is large enough to take hard knocks well within its rating.

  • Rear2 x 6902 and 1 x ACB41H6.5 angular contact
  • Front6902 and 6802
  • PreloadSet by hand with the non-drive side collar; checked again after three rides
The 41.5 mm nano-coated angular contact bearing of the Helix-01 rear hub

Built like a gearbox

Forged where it can be, machined where it must be.

Venn took the Helix-01 from an early prototype to a hub we are proud to sell: we redesigned how its 41.5 mm angular contact bearing sits in the shell, the preload system, the shell shape and the axle, and made the freehub one piece of alloy. It is built with the forging and surface treatment that Taiwan's automotive industry already runs at the highest standard, and it is made in Taiwan.

Cold-forged Helix-01 rear hub shell

Cold-forged shell

Cold forging aligns the aluminium's grain with the shape of the part, for strength that machining alone cannot give. Shot-peened grey, laser-etched logo.

Helix-01 72-tooth ratchet rings and helical drive

Gearbox-grade ratchet

Custom-forged SCM 415 steel, CNC machined and manganese phosphate coated: the treatment car gearboxes use to cut friction and hold lubricant.

Helix-01 15 mm threaded axle

15 mm threaded axle

7075-T6 hardened aluminium. A steel axle for e-bikes and tandems is available on wholesale orders.

Helix-01 hardened alloy freehub body

Hardened freehub

Shimano HG, SRAM XDR or Shimano Micro Spline. A steel freehub for e-bikes and tandems is available on wholesale orders.

Helix-01 flat steel ratchet spring

Flat steel spring

More contact area and strength than a round wire spring, so engagement starts evenly every time.

Exploded view of the Helix-01 rear hub

Simple to service

Disassembly is straightforward, and the sealed ratchet needs little care. Lithium-based grease is all it asks for. Care and service guide (PDF)

Weight

348 grams, carried where they cost least.

The Helix-01 is not built to be a weight-weenie hub: its grams go into the gears, the oversize bearing and the forged shell. It is still lighter than many high-engagement hub sets.

And hub weight sits 2 to 3 cm from the axle, where it adds almost nothing to the wheel's rotating inertia: when you accelerate, a gram at the hub costs about half of a gram at the rim. Built into our 520 HE1 road wheelset, the whole set weighs 1,280 g.

24-hole hubs, 12 x 100 / 12 x 142 mm, alloy axle.

Specifications

Venn Helix-01 hub set

Engagement72-tooth helical gear ratchet, 5°
BrakeDisc, Center Lock
Hole counts24h front and rear, 28h front and rear, 28h Boost front and rear
Axles12 x 100 mm front, 12 x 142 mm rear; Boost 15 x 110 mm front, 12 x 148 mm rear
FreehubsShimano HG, SRAM XDR, Shimano Micro Spline; steel freehub on wholesale orders only
WeightFront 105 g, rear 243 g
Rider weight limit110 kg (24h), 130 kg (28h)
BearingsRear: 2 x 6902, 1 x ACB41H6.5 angular contact; front: 6902, 6802
ShellCold-forged aluminium, shot-peened grey, laser-etched logo
Axle15 mm, 7075-T6 aluminium; steel on wholesale orders only
RatchetSCM 415 steel, forged, CNC machined, manganese phosphate coated
Made inTaiwan
Warranty2 years

For wheel builders

24h straight pull. All figures in mm.

Front hub, 12x100, OLD 100

SideSpoke circle ØCentre to flangeSpoke offset
Disc side44.522.21.9
Open side35.231.22.0

Rear hub, 12x142, OLD 142

SideSpoke circle ØCentre to flangeSpoke offset
Disc side40.532.72.3
Drive side57.517.22.5

Spoke holes 2.6 mm, head seat 4.2 mm. Offsets measured at the spoke-head seat.

Lacing: 2-cross.

HE1 wheelsets

Or ride it already built.

Three Venn wheelsets are built on the Helix-01: Venn carbon rims, Sapim CX-Ray spokes, and no clear coat, in gloss, matte or 25k filament wound.

Price

One price for the hub set.

Venn Helix-01 hub set

$449
About €409. Front and rear hub.
  • Front and rear hub, 24h, 12 x 100 / 12 x 142 mm thru axle
  • Freehub of your choice: Shimano HG, SRAM XDR or Shimano Micro Spline
  • Assembled, ready to lace
  • 2-year warranty
Order on venn-cycling.com

Wheel builders and shops

From 10 sets: trade prices, plus the 28h and Boost versions, and the steel axle and steel freehub, which are wholesale only. Tell us what you build and we will quote.

  • Minimum order 10 sets
  • 24h, 28h and 28h Boost
  • Shimano HG, SRAM XDR, Shimano Micro Spline
  • Steel axle and steel freehub for e-bikes and tandems
Ask for trade prices

Questions

Frequently asked

What does helical engagement do?

In an ordinary ratchet hub, springs alone hold the drive rings together and a little play remains between the teeth. The Helix-01 engages the way a bolt tightens: the harder you pedal, the firmer its two 72-tooth ratchet rings press together. Under power there is no free play, and your effort goes into the wheel at once.

Why an angular contact bearing?

A wheel under a rider is loaded from the side as well as from above. Ordinary cartridge bearings spin freely in the hand, but their friction rises under those side loads; an angular contact bearing is made for them. The oversize 41.5 mm bearing keeps the rear hub rolling freely on the road, not only in a workstand, and takes hard knocks well within its rating.

How is the bearing preload adjusted?

Angular contact bearings need a light preload: no free play, but not so tight that the bearing rolls poorly. On the bike with the chain off, tighten the non-drive side preload collar by hand until the wheel has no side-to-side play but still turns freely on the axle, then tighten its bolt. Check it again after three rides, or sooner if it feels loose; once the bearing has settled it needs no further adjustment in normal use.

Which bikes does it fit?

Disc brake bikes with thru axles: 12 x 100 mm front and 12 x 142 mm rear for road and gravel, Boost 15 x 110 mm and 12 x 148 mm for MTB (28 hole). Freehubs for Shimano HG, SRAM XDR and Shimano Micro Spline. There is no rim brake or Campagnolo version.

How do I service it?

Disassembly is straightforward. The ratchet is sealed from the elements and its steel is manganese phosphate coated against corrosion, so it needs little care. Use lithium-based grease when you service it. Care and service guide (PDF)

Why does it cost less than the best-known premium hubs?

We put our engineering into the bearing seating, the preload system, the shell, the axle and the one-piece alloy freehub, and built it with processes Taiwan's automotive and semiconductor industries already run at scale: forged gears and the coatings that car gearboxes use. We did not need to reinvent proven processes, and there is no retail chain to pay for.

What is the warranty?

Two years against defects in materials and workmanship.